Joyetech eGrip II Light • Starter Kit • 80W TC 2100 mAh 3.5 ml

$74.00

Joyetech eGrip II All-in-One Starter Kit

eGrip II Light
eGrip II Light
eGrip II Light, a new version of eGrip II, crafted from super light magnesium alloy has a deep, high-gloss finish of multiple colors. The eGrip II Light adopts the best anti-leaking structure with top refilling and top airflow control system. Large 0.96 inch OLED screen, clock screensaver and multiple tank lights all make it more practical and attractive catering to your preference. Meanwhile, upgradeable firmware always enables it up-to-date.
Standard Configuration:

1*eGrip II Light Body
1*NotchCoilTM 0.25ohm DL .
1*BF SS316 0.5ohm DL .
1*BF Clapton 1.5ohm MTL .
1*BF RBA M&L (Vertical)
2*Mouthpiece
1*Atomizer Adapter(for eGrip II Light)
1*USB Port
1*Manual & Warranty Card
1*Warning Card


eGrip II Light
Specification:
Size: 24.00*45.00*100.55mm
Weight: 129g
Output Mode: RTC/VW/VT(Ti, Ni, SS316)/Bypass/TCR(M1, M2, M3)
Output Wattage: 1-80W
Battery Capacity: 2100mAh
E-liquid Capacity: 3.5ml
Resistance Range: 0.05-1.5ohm for VT mode
0.1-3.5ohm for VW/BYPASS mode
Temperature Range: 100-315°C/ 200-600°F
Colors: Blue Wrinkle, Black Wrinkle, Orange Wrinkle, Red Wrinkle
eGrip II Light
Magnesium alloy, super light
Crafted from magnesium alloy, our new eGrip II Light has a deep, high-gloss finish of multiple colors.
It only weighs (129g) nearly half of the eGrip II (210g).
eGrip II Light
RTC (Real Time Clock) on display
eGrip II Light applies the RTC (Real Time Clock) function.
It enables you to switch between digi clock and analog clock. Also, you can set it as screensaver.
eGrip II Light
Dual Circuit Protection
eGrip II Light applies two sets of battery protection circuit system, realizing overall battery protection of
over-charging, over-current and over-discharging, which makes it more safe and reliable.
eGrip II Light
eGrip II Light applies NotchCoilTM 0.25ohm DL. Head
eGrip II Light uses NotchCoilTM 0.25ohm DL. (Direct Lung) head lasts longer and can be used under high wattage condition.
It will surely bring you great vaping experience ever.
eGrip II Light
NOTE:1.Please do not wash the atomizer head with water. Simply scrub it with cotton or clean dry cloth.
2.Please drip at least 5 drops of e-juice to the atomizer head and vape a few times in power-off
condition (with airflow widely open) before its first use to avoid dry burn.
Top Filling And Top Airflow Control
eGrip II Light
The eGrip II Light airflow control system allows larger airflow inlet directly from both sides. Simply rotate the airflow ring clockwise or counter-clockwise to adjust the airflow inlet. eGrip II Light
eGrip II Light E-juice filling can be easily achieved by removing the top cap and injecting through the two side holes (not the vent pipe)
Fashionable Tank Lights
Multiple colors of tank lights make eGrip II Light more attractive and fashionable catering to your preference.
eGrip II Light
Apply the Atomizer Adapter
Unscrew the airflow ring and remove the whole part. Screw the atomizer adapter tightly with a coin,
then you're able to apply multiple types of atomizers with the 510 pin.
eGrip II Light
Firmware Upgradeable
eGrip II Light comes with the upgradeable firmware.
The latest firmware version 5.04 for eGrip II Light with new interface and preheat function are now available.
eGrip II Light
eGrip II Light
Multiple Atomizer Heads Can Be Applied
NotchCoilTM 0.25ohm DL . head, BF SS316 Series Heads, BF Clapton-1.5ohm head, BF Ni, BF Ti and BF RBA head.
eVic AIO
Multiple BF Series Heads for Your Choice
eGrip II Light
How to Reset The Device
eGrip II Light
Charging & Upgrading
The micro USB port is on the top of the left side. Connect it with a micro USB cable to charge or upgrade your device. Simply charge eGrip II Light by connecting it with the wall adapter or a computer via USB cable. The battery is charged as shown in the picture. When it is fully charged, the charging bar will disappear.
eGrip II Light

 

Related products